Ero sivun ”WLAN/en” versioiden välillä
(Ak: Uusi sivu: NOTE, the AP must be configured to permit wds connections.) |
(Ak: Uusi sivu: * ''manual'' All data must manually be defined their transmit power.) |
||
| (13 välissä olevaa versiota samalta käyttäjältä ei näytetä) | |||
| Rivi 14: | Rivi 14: | ||
==== ap-bridge ==== | ==== ap-bridge ==== | ||
| − | + | Basic access point | |
==== bridge ==== | ==== bridge ==== | ||
| − | + | Same as "ap-bridge", but only allows one connected client at a time. | |
==== alignment only ==== | ==== alignment only ==== | ||
| − | + | Sets the interface to continuous transmitting state which directs all traffic to an external antenna. | |
==== nstreme-dual-slave ==== | ==== nstreme-dual-slave ==== | ||
| − | + | Permits the interface to be used with nstreme-dual | |
==== wds-slave ==== | ==== wds-slave ==== | ||
| − | + | Same as "ap-bridge", but scans the access point's ssid and establishes a wds-link. If the link is severed, it will keep scanning. | |
==== station-pseudobridge ==== | ==== station-pseudobridge ==== | ||
| − | + | Same as "station", but adds MAC-address faking to all traffic. | |
==== station-pseudobridge-clone ==== | ==== station-pseudobridge-clone ==== | ||
| − | + | Same as "station-pseudobridge", but uses "station-bridge-clone-mac" address to connect to the access point. | |
==== station-bridge ==== | ==== station-bridge ==== | ||
| − | + | In this state the AP keeps a distributable table of mac-addresses which it has been given from client machines or from other access points' tables. | |
| − | == | + | == Small adjustments == |
=== tx-power-mode === | === tx-power-mode === | ||
| − | + | Here we define the tx-power (transmit) state on the wireless interface. Default setting is "Default". | |
* ''all rates fixed'' | * ''all rates fixed'' | ||
| − | + | Uses the same transmit power for all data. | |
* ''card rates'' | * ''card rates'' | ||
| − | + | Uses those transmit settings which have been defined in Tx power's settings. | |
* ''default'' | * ''default'' | ||
| − | + | Uses those settings which came by default in the WLAN interface card. | |
* ''manual'' | * ''manual'' | ||
| − | + | All data must manually be defined their transmit power. | |
Nykyinen versio 21. heinäkuuta 2015 kello 05.54
Sisällysluettelo
Different modes
station
Basic station. Find and connects to a suitable access point.
station-wds
Same as "station", but creates a wds bridge with the AP using proprietary extension.
NOTE, the AP must be configured to permit wds connections.
ap-bridge
Basic access point
bridge
Same as "ap-bridge", but only allows one connected client at a time.
alignment only
Sets the interface to continuous transmitting state which directs all traffic to an external antenna.
nstreme-dual-slave
Permits the interface to be used with nstreme-dual
wds-slave
Same as "ap-bridge", but scans the access point's ssid and establishes a wds-link. If the link is severed, it will keep scanning.
station-pseudobridge
Same as "station", but adds MAC-address faking to all traffic.
station-pseudobridge-clone
Same as "station-pseudobridge", but uses "station-bridge-clone-mac" address to connect to the access point.
station-bridge
In this state the AP keeps a distributable table of mac-addresses which it has been given from client machines or from other access points' tables.
Small adjustments
tx-power-mode
Here we define the tx-power (transmit) state on the wireless interface. Default setting is "Default".
- all rates fixed
Uses the same transmit power for all data.
- card rates
Uses those transmit settings which have been defined in Tx power's settings.
- default
Uses those settings which came by default in the WLAN interface card.
- manual
All data must manually be defined their transmit power.
wds-mode
- disabled
- dynamic
- dynamic mesh
- static
- static mesh
wireless-protocol
- 802.11
- any
- nstreme
- nv2
- nv2 nstreme
- nv2 nstreme 802.11
- unspecified
